=========================================================== Lucent Technologies Mar 2, 2000 WaveLAN/IEEE Software for Linux, Version: 6.00 =========================================================== This text file includes update information, installation instructions, limitations to the current version of the product, and suggestions to solve known issues or problems. TABLE OF CONTENTS. 1. SOFTWARE DESCRIPTION 2. SYSTEM REQUIREMENTS 3. NEW IN THIS RELEASE 4. INSTALLATION NOTES 5. TECHNICAL CONSTRAINTS 6. KNOWN ISSUES 7. TECHNICAL SUPPORT ----------------------------------------------------------- 1. SOFTWARE DESCRIPTION 1.1 Description This software is officially released and supported software of Lucent Technologies Inc. 1.2 Software Components This software for the WaveLAN IEEE Turbo 11 Mb PC Card is distributed in a compressed archive: * wavelan2_cs-6.00.tar.gz This archive contains driver source files and a library. You can use these files to build and install a WaveLAN/IEEE PC Card driver for your specific Linux kernel. The current set of driver source files supports Linux kernel versions 2.0.x through 2.2.x for the Intel architecture, as included (for example) with the following Linux Distributions: * Red Hat version 5.2, 6.0, 6.1 * Suse version 6.1 The included HCF library implements an interface to the Lucent Technologies 802.11 MAC Controller, used in the WaveLAN/IEEE environment. Designed for the WaveLAN/IEEE Turbo 11 Mb PC Cards, you can also use this software to install and operate previous versions of WaveLAN/IEEE PC Cards, like the: * Standard White & Bronze label PC Cards * Turbo Bronze label PC Cards * Silver Label PC Cards 1.3 Software Versions The following software is included with this WaveLAN/IEEE distribution: General information: * README.wavelan2_cs This file * LICENSE.wavelan2_cs License * wavelan2_cs.mk Top level Makefile Driver source and HCF library: * clients/wavelan2_cs.mk Driver Makefile * clients/wavelan2_cs.c Driver source (v6.00) * include/hcf/debug.h Driver debug support * include/hcf/libhcf.h HCF interface definition * lib/libhcf-i386.a HCF library (v4.6a) Driver online manual page: * man/wavelan2_cs.4 Driver manual page PCMCIA configuration update: * etc/wavelan2_cs.conf Add-on config file * etc/wavelan2_cs.mk config update Makefile * etc/wavelan2_cs.patch config update patch file ----------------------------------------------------------- 2. SYSTEM REQUIREMENTS 2.1 Operating System This software can be compiled and installed on systems running a Linux kernel versions 2.0.x through 2.2.x for the Intel architecture. 2.2 Free Disk Space To compile the software you will need to have the full set of Linux kernel source files installed. Depending on the exact version of the kernel, you will need approximately 65 MB of free disk space. Once compiled, the driver will use approximately 38 kB. ----------------------------------------------------------- 3. NEW IN THIS RELEASE Version 6.00 - March 2, 2000 * Corrected setting of mac_address parameter on pre-2.1.0 kernels * Corrected number of IO Ports (=0x40) * Corrected dbm() function * Added support for Microwave Oven Robustness * Added iwspy support, thanks to Dan Forsberg and Jim Binkley * Added support for 3.3/5 Volt cards * Added etc/wavelan2_cs.conf Version 4.00 - July 2, 1999 * Added support for WEP encryption * Corrected string transfer of private ioctls used by the Wireless extensions. * Support for signal levels in dBm; reported by the Wireless extensions. * Support for CFG_DRV_IDENTITY moved from HCF to MSF. * Validate module parameters by default. This was only enabled in debug mode in the previous versions. * Fixed Card Power Management bug. Version 3.10 did not enable PM on standard (2 Mbit/s) cards with STA firmware 2.00, when configured to enable PM. * Corrected module parameter type of irq_mask (h = short) and irq_list (1-4b = 1-4 bytes). Version 3.10 - April 28, 1999 * Changes to allow for the module parameter differences between Linux 2.0 and Linux 2.1. Linux 2.0 only allowed for 32-bit integer parameters, the 2.1 or later kernels allow for 8, 16 and 32 bit parameters. * Added BSD clause to the GPL license. * Added support for Linux Wireless extensions. * Fixed the setting of the network_name and station_name when the name was empty or set to ANY for network_name. * The user can now enable Card Power Management: PLEASE NOTE: This function should not be enabled until software that supports Card Power Management will be installed on both: - PC Card (Use Station Functions firmware v2.00 or higher) and - WavePOINT-II Access Point (use AP software v2.03 or higher) , In case you enable Card Power Management without having updated the firmware to version levels listed above, the driver will not effectuate Card Power Management. * Added support for transmit timeout handling. * Re-added channel parameter. * Renamed parameter receive_all_multicast to receive_all_multicasts * Changed the values of the parameters card_power_management and receive_all_multicasts to 'Y' for Enable and 'N' for Disable. Version 1.27 (Beta-2) - March 2, 1999 First Source/Library distribution. * Changed module parameters names to better conform to the PCMCIA and 802.11 naming conventions. Version 1.20 (Beta-1) - February 9, 1999 Binary only version for Slackware 3.6 (linux 2.0.35) and RedHat 5.2 (linux 2.0.36). ----------------------------------------------------------- 4. INSTALLATION NOTES The driver files for the Linux driver are not "ready" for direct installation onto any Linux computer. To build and install the driver you will need some expertise on the Linux operating system in general and the type and version installed of the kernel installed on your computer. With this knowledge you can use the driver source files provided to build your own Linux driver for your specific computer and kernel. 4.1 Before you start 1) Determine the type and version of the Linux kernel of your computer and check whether it meets the system requirements listed in section 2 of this README. 2) Read the Linux PCMCIA-HOWTO by David Hinds. This document is probably provided on a CD-ROM of your Linux distribution. You can download the latest version from: http://pcmcia.sourceforge.org Please read the section titled "Prerequisites and kernel setup" of the PCMCIA-HOWTO. 4.2 Build the WaveLAN/IEEE Driver 1) Obtain a copy of the Linux PCMCIA package from a CD-ROM of your Linux distribution or download the latest version from: http://pcmcia.sourceforge.org 2) Unpack the Linux PCMCIA package. % tar xzvf pcmcia-cs-3.1.8.tar.gz 3) Extract the WaveLAN/IEEE distribution archive on top of the Linux PCMCIA package. % cd pcmcia-cs-3.1.8 % tar xzvf ../wavelan2_cs-6.00.tar.gz 4) Build and install the PCMCIA package as described in the PCMCIA-HOWTO. % make config % make all % su .. # make install 4.3 Configure your WaveLAN/IEEE PC Card 1) To configure the WaveLAN/IEEE PC Card, please refer to: * The WaveLAN/IEEE manual page (wavelan2_cs.4) % man wavelan2_cs * The network adapter sections of the PCMCIA documentation. % more PCMCIA-HOWTO 2) Use an editor to configure the module parameters: # vi /etc/pcmcia/config.opts For example: a) To connect your computer to an Ad-Hoc workgroup of wireless computers enter the following in the config.opts file: module "wavelan2_cs" opts "port_type=3" This is the typical setting for connecting individual computers to a peer-to-peer network, in environments without a dedicated access point. b) To connect your computer to a wireless infrastructure that includes access points such as the Lucent Technologies WavePOINT-II, you will need to identify the network name of the wireless infrastructure. For example if your infrastructure uses the network name "My Network", edit the config.opts file to include the following: module "wavelan2_cs" opts "network_name=My\ Network" Notice that the space character needs to be escaped with a backslash. c) Optionally you can also include a "Station Name" value that can be used to indentify your computer on the wireless network. For example if you wish to name your computer "Wave1" when connecting it to a wireless infrastructure, edit the config.opts file to include the following: module "wavelan2_cs" opts "network_name=Ocean station_name=Wave1" 3) Use an editor to modify the network options for your adapter. # vi /etc/pcmcia/network.opts The parameters need to be correct for the connected network. Check with your system administrator for the correct network information. Refer to the PCMCIA-HOWTO for more configuration information. For example: *,*,*,*) IF_PORT="" BOOTP="n" IPADDR="10.0.0.5" NETMASK="255.255.255.0" NETWORK="10.0.0.0" BROADCAST="10.0.0.255" GATEWAY="10.0.0.1" DOMAIN="domain.org" DNS_1="dns1.domain.org" ;; 4) Restart the PCMCIA services. # /etc/rc.d/rc.pcmcia restart or # /etc/rc.d/init.d/pcmcia restart For a more detailed description about the various configuration options and definitions, please consult the 'Getting Started Guide' that was provided on the WaveLAN Software CD-ROM in Adobe's Acrobat PDF. WaveLAN User documentation is also available in electronic format on the WaveLAN Web Site. (http://www.wavelan.com). You can download the documentation in Adobe's Acrobat Portable Document Format (PDF). To view or print PDF files you will need the freeware Acrobat Reader that can be downloaded from the Adobe Web Site (http://www.adobe.com/acrobat) 4.4 Troubleshooting When the WaveLAN/IEEE PC Card is inserted, the card manager will emit beeps in different tones to indicate success or failure of particular configuration steps. a) Two high beeps - The card was identified and configured successfully. b) One high beep followed by a low beep - The card was identified, but could not be configured. - Examine the system log (dmesg) for PCMCIA error or warning messages. c) One low beep - The card could not be identified. - Execute "cardctl ident" to display the adapter PnP information. Verify the PnP information matches an entry in the PCMCIA configuration file (/etc/pcmcia/config). - Examine the system log (dmesg) for PCMCIA error or warning messages. The WaveLAN/IEEE PC Card has two LEDs that indicate the state of the adapter and network. * Power LED (toward the middle of the adapter) - This LED indicates power has been applied, and the card is functional. In normal operation mode with Card Power Management disabled, it will be steady-on. With Card Power Management enabled, it will blink rapidly (several times per second). * Transmit/Receive LED (closer to the edge of the adapter) - This LED will flash when it detects transmit or receive packets. * Both LEDs blink at the same time every 10 seconds. - The adapter was unable to make contact with the named wireless network. Verify the network_name, in the config.opts file matches the network name of the access point. * LEDs indicate normal operation with the Power LED steady-on or blinking rapidly and Transmit/Receive LED flashing, but no traffic. - If the network is operating in normal mode (ie. port_type = 0 or not specified), and a network_name has been specified, verify the workstation network parameters (ifconfig, route, etc.) are correct for the wireless network. - If the network is operating in Ad-Hoc (peer-to- peer) mode (ie. port_type = 3), the adapter needs another workstation/adapter to communicate with. Verify the network parameters on both of the workstations (ifconfig, route, etc.) are correct. Refer to WaveLAN/IEEE manual page for additional configuration, feature and support information. % man wavelan2_cs or % man 4 wavelan2_cs or % nroff -man wavelan2_cs.4 | more 4.5 Wireless extensions This driver has some support for the "Wireless Extensions". This interface allows the "Wireless Tools" to get statistics from the driver and allows to change the configuration of the driver on the fly. For more information, refer to the following WEB pages: http://www.hpl.hp.com/personal/Jean_Tourrilhes/Linux/Linux.Wireless.Extensions.html http://www.hpl.hp.com/personal/Jean_Tourrilhes/Linux/Tools.html 4.6 Identifying the software This section explains how to identify the version of this software once it is unpacked or installed. The Linux Driver Source/Library distribution consist of two main components, the driver source and the HCF library. * To quickly identify the wavelan2_cs.c source, type: % grep wavelan2_cs.c wavelan2_cs.c "wavelan2_cs.c 6.00 03/02/2000 11:00:00 (Lucent Technologies)"; * To identify the revision of the HCF library, type: % strings libhcf-i386.a | grep Revision HCF$Revision: 4.6 To identify a compiled wavelan2_cs.o driver, go to the directory where the driver is located. Installed drivers are normally located in: /lib/modules//pcmcia * To retrieve the version of the source used to compile the driver, type: % strings wavelan2_cs.o | grep wavelan2_cs.c wavelan2_cs.c 6.00 03/02/2000 11:00:00 (Lucent Technologies) * To retrieve the revision of the HCF library used to compile the driver, type: % strings wavelan2_cs.o | grep Revision HCF$Revision: 4.6 ----------------------------------------------------------- 5. TECHNICAL CONSTRAINTS At the time of release of this software, the following constraints are identified: 5.1 Using the WaveLAN/ISA adapter Description: The WaveLAN/IEEE solutions was designed as a one-card solution, providing the same PC Card type for operation in standard Type II PC Card slots of either: * laptop computers or * Lucent Technologies WavePOINT-IIs. To allow operation in desktop computers Lucent also provides an optional ISA bus to PC Card adapter (also referred to as "swapbox"). This WaveLAN ISA Adapter can be configured for two different I/O Address values: * 3E2 (factory-set default) * 3E0 Impact: By default the i82365 module of the Linux pcmcia package will only probe at 3E0. Action: 1) Read the manual page on the probing of the i82365 module, by typing the command: man i82365 2) Apply one of the two following options: a) Change the I/O address strapping of the ISA card by replacing the jumper on the ISA board. The correct jumper setting is pictured in Figure C-1 of Appendix C in the electronic user's guide provided on the WaveLAN Software CD-ROM. This guide is provided in Adobe's Acrobat PDF format. b) Alternatively, you can load the i82365 module with the "extra_sockets" parameter set to 1. On a RedHat 5.2 system, put this in the file "/etc/sysconfig/pcmcia": PCMCIA=yes PCIC=i82365 PCIC_OPTS="extra_sockets=1" CORE_OPTS= CARDMGR_OPTS= For other Linux distributions, you are advised to consult the "PCMCIA-HOWTO" notes for information about changing the I/O Address probing. 5.2 Station functions compatibility Description: This driver supports cards with secondary firmware version 4.x and higher. Impact: The driver will abort and generate the following error message in the system log file (/var/log/messages): eth0: WaveLAN/IEEE, HCF failure: "Primary functions are compatible, station functions are not" Action: You are advised either to: a) Use the WaveLAN Station Update tool, (for example WSU10430.exe) on a Windows system with a working WaveLAN driver. b) Or revert to version 4.00 of this driver (wavelan2_cs-4.00.tar.gz). 5.3 Building a bridge or router Description: The Linux driver uses the station firmware programmed in Flash memory on the WaveLAN/IEEE card. On an IEEE 802.11 Station you can not build a MAC-layer Transparent Bridge. This is not a restriction of WaveLAN/IEEE only; it is an architectural restriction of IEEE 802.11. As such it is specified in the 802.1D Bridge Standard (1998 Edition): A Bridge to an 802.11 LAN shall connect to an 802.11 Portal, which in turn connects to an 802.11 Distribution System. As the Distribution System is part of the AP (and not of the STA), you need an AP to build a Bridge. The major cause for this is the MAC-layer Acknowledgement. A Transparent Bridge will have to Ack frames destined for multiple destinations (everything that is not in the cell itself). An AP can do this; a STA can not; by definition. Action: It is possible to build a router using this driver. ----------------------------------------------------------- 6. KNOWN ISSUES At the time of release of this software, the following problems remain to be solved: none ----------------------------------------------------------- 7. TECHNICAL SUPPORT 7.1 Finding Information On the WaveLAN Web Site you can find the most recent device drivers, bridge firmware, software updates and user documentation. World Wide Web: HTTP://WWW.WAVELAN.COM or FTP://FTP.WAVELAN.COM/PUB 7.2 Contact Technical Support If you encounter problems when installing or using this product, or would like information about our other WaveLAN products, please contact your local Authorized WaveLAN Reseller or Lucent Technologies Sales office. Addresses and telephone numbers of the Lucent Technologies Sales offices are listed on our WaveLAN Web Site. When contacting WaveLAN Technical Support, please use the Problem Report Form and send it to us by Fax or E-Mail. The Problem Report Form 'REPORT.TXT' (Plain text format) is included with the software diskette, or downloaded set of files. Alternatively, you can download the Problem Report Form from the WaveLAN Web Site. Include Product Name, Serial Number and software version number with each request to help the WaveLAN Support Group helping you. In emergency, or when no local support is available, you can reach WaveLAN Regional Support via email: - - - - - - - - - - - - - - - - - - - - - - - - USA & Canada usasupport@wavelan.com - - - - - - - - - - - - - - - - - - - - - - - - Europe, Middle-East & emeasupport@wavelan.com Africa - - - - - - - - - - - - - - - - - - - - - - - - Caribean, Latin America calasupport@wavelan.com - - - - - - - - - - - - - - - - - - - - - - - - Asia and Pacific: apasupport@wavelan.com - - - - - - - - - - - - - - - - - - - - - - - - OEM: oemsupport@wavelan.com - - - - - - - - - - - - - - - - - - - - - - - - When you would like to report a problem releated to BETA SOFTWARE, please send an email to: betasupport@wavelan.com. =========================================================== END OF FILE