[ Quick Installation ]
[ 快速安裝  ]

  1. Reboot into DOS or Command Prompt only of Windows 95
     重開機到 DOS.
  2. Copy DOS4GW.EXE, BIOSLOAD.EXE and BIOS.BAT to a new directory from
     Utility disk.
     Copy the new BIOS binary file to the new directory
     拷貝 BIOSLOAD.exe, DOS4GW.exe 及您所選擇的二進位檔案到新的目錄.
  3. Enter the new directory and type the following command :
     BIOS [Filename]
     於該目錄下鍵入 BIOS [*.BIN]
  4. Wait for at least 10 seconds before rebooting if the display go blank
     or flicker.
     升級寫入動作須要 10 秒.螢幕顯示出許多表示處理中的記號(..... or OOOO or XXXXX).
     若您的卡先前已經被升級到較新的版本,則升級寫入動作將會非常快速,因為只有寫入少數
     不同的部份.
     *在某些螢幕可能會產生螢幕消失或跳動現象,請耐心等待至少 15 秒後再重開機.
     

[ Section B.] BIOS UPDATE PROCESS : *****************************************
[ 一般正常安裝 ]

This pack consists of the following files:-
包含的檔案及用途:-

BIOSLOAD.exe The DOS utility for fast loading the video BIOS into the ATMEL 29LV512 
             (The AMD BIOS ROM is not available) flash programmable EPROM used on 
             WinFast 3D L2300 PCI/AGP boards. This program requires 'DOS4GW.exe' 
             (supplied)
             於 DOS 下快速升級載入 Video BIOS (.BIN) 至顯示卡上的可抹寫式記憶體.
             DOS4GW.EXE 在 BIOSLOAD.EXE 中被起動執行,不能缺少.
             *可抹寫式記憶體型號必須是 ATMEL 29LV512 版本,AMD 的版本不能使用.

*.bin        New BIOS files suitable for immediate loading onto WinFast 3D L2300 
             AGP/PCI boards.  Use the following table to decide which file is 
             suitable for your board.
             新的顯示卡的硬體驅動程式(二進位檔案).請依下表選擇您顯示卡類型並且下載
             您所需的(二進位檔案).

             NOTE: it is important that you choose the correct file to load onto
                   a card.  CHOOSING THE WRONG FILE MAY PREVENT YOUR MACHINE BOOTING.
             注意:選擇錯誤的二進位檔案,並升級至顯示卡上的可抹寫式記憶體,將有可能使
                  您的系統無法開機.

             Card to be upgraded      Appropriate file
             (欲升級的顯示卡類型)     (相對應的二進位檔案)
             ---------------------------------------------
             WinFast 3D L2300 PCI      PCI.bin
             WinFast 3D L2300 AGP      AGP.bin

----------------------------------------------------------------------------------
LOADING THE BIOS onto WinFast 3D L2300 PCI/AGP boards.
升級步驟:

  1. Create a suitable directory on floppy or hard disk.
     於硬碟或軟碟中新開一個目錄,並予以適當的命名.
  2. Copy BIOSLOAD.exe, DOS4GW.exe and your chosen .bin file into this folder. 
     (See table above for .bin selection).
     拷貝 BIOSLOAD.exe, DOS4GW.exe 及您所選擇的二進位檔案到該目錄.
  3. Reboot into DOS.
     重開機到 DOS 下(請勿進入 Win95).
  4. Change into the newly created directory.
     更換路徑到先前所開啟的目錄.
  5. Type: BIOSLOAD -r -f filename.bin
     Programming can take up to 10 seconds.  Progress is shown as several lines
     of dot,'O' or 'X' characters.  If your card already contains the same BIOS as
     the one being loaded the program will finish almost immediately as it only
     loads those parts which are different.  On some machines the display may go
     blank or flicker.  If this happens simply wait for at least 15 seconds before
     rebooting.
     鍵入 BIOSLOAD -r -f filename.bin
     升級寫入動作須要 10 秒.螢幕顯示出許多表示處理中的記號(..... or OOOO or XXXXX).
     若您的卡先前已經被升級到較新的版本,則升級寫入動作將會非常快速,因為只有寫入少數
     不同的部份.
     *在某些螢幕可能會產生螢幕消失或跳動現象,請耐心等待至少 15 秒後再重開機.
  6. Reboot and check the startup screen shows the correct video BIOS version and
     date as shown at the beginning of this file.
     重新開機,起動的螢幕上將顯示正確的 Video BIOS 版本及日期.