EXAMPLES

Reboot
<rci_request version="1.1">
<reboot>
</reboot>
</rci_request>

Query all settings:
<rci_request version="1.1">
<query_setting/>
</rci_request> 

Query only boot and serial settings:
<rci_request version="1.1">
<query_setting>
<boot/>
<serial/>
</query_setting> 
</rci_request> 


Query only device settings:
<rci_request version="1.1">
<query_setting>
<device_info/>
</query_setting> 
</rci_request> 

Query only GPIO pin states:
<rci_request version="1.1">
<query_state>
<gpio/>
</query_state> 
</rci_request> 

Setting IP address:
<rci_request version="1.1">
<set_setting>
<boot>
<static>on</static> 
<dhcp>off</dhcp> 
<autoip>on</autoip> 
<ip>10.4.112.15</ip> 
<subnet>255.255.0.0</subnet> 
<gateway>10.4.1.1</gateway> 
<eth_speed>auto</eth_speed> 
<eth_duplex>half</eth_duplex> 
</boot>
</set_setting>
</rci_request> 

Setting dynamic IP address:
<rci_request version="1.1">
<set_setting>
<boot>
<static>off</static> 
<dhcp>on</dhcp> 
<autoip>off</autoip> 
</boot>
</set_setting>
</rci_request> 

Configuring serial port #1 for TCP Sockets mode with serial settings 9600 baud 8 data bits, no parity, 1 stop bit, no flow control:
<rci_request version="1.1">
<set_setting>
<profile>
<profile_type>tcp_sockets</profile_type> 
</profile>
<serial>
<baud>9600</baud> 
<databits>8</databits> 
<stopbits>1</stopbits> 
<parity>none</parity> 
<flowcontrol>none</flowcontrol> 
</serial>
</set_setting>
</rci_request> 

Configuring for wireless WPA Authentication via username and password
<rci_request version="1.1">
<set_setting>
<boot>
<static>off</static> 
<dhcp>on</dhcp> 
<autoip>on</autoip> 
<ip>0.0.0.0</ip> 
<subnet>0.0.0.0</subnet> 
<gateway>0.0.0.0</gateway> 
<channel>0</channel> 
<wep_type>64bit</wep_type> 
<wepkey_index>1</wepkey_index> 
<protocol_mode>any</protocol_mode> 
<ssid>Connect</ssid> 
<rts_threshold>2347</rts_threshold> 
<fragment_threshold>2346</fragment_threshold> 
<max_txrate>11MB</max_txrate> 
<country_code>United States</country_code> 
<authentication>wpa_auth</authentication> 
<encrypt>open,wep,tkip,ccmp</encrypt> 
<eap>leap,peap,tls,ttls,gtc,md5,mashapv2,otp,ttls-chap,ttls-mschap,ttls-mschapv2,ttls-pap</eap> 
<options /> 
<txpower>14dbm</txpower> 
<wpa_username>administrator</wpa_username>
<wpa_password>himom</wpa_password>
</boot>
</set_setting>
</rci_request> 



Toggling GPIO pin #1 into a low (unasserted) state:
<rci_request version="1.1">
<set_state>
<gpio_mode>
<pin1>out</pin1>
</gpio_mode>
<gpio>
<pin1>unasserted</pin1>
</gpio>
</set_state>
</rci_request> 





TCP autoconnect using SSL
<rci_request version="1.1">
<set_setting>
<profile>
<profile_type>tcp_sockets</profile_type> 
</profile>
<serial>
<baud>9600</baud> 
<databits>8</databits> 
<stopbits>1</stopbits> 
<parity>none</parity> 
<flowcontrol>none</flowcontrol> 
</serial>
<autoconnect>
<state>on</state>
<trigger>data</trigger>
<service>ssl</service>
<desc></desc>
<address>10.4.112.9</address>
<port>3333</port>
<pattern></pattern>
<strip_pattern>off</strip_pattern>
<keepalive>on</keepalive>
<nodelay>off</nodelay>
</autoconnect>
</set_setting>
</rci_request> 



TCP autoconnect using raw TCP
<rci_request version="1.1">
<set_setting>
<profile>
<profile_type>tcp_sockets</profile_type> 
</profile>
<serial>
<baud>9600</baud> 
<databits>8</databits> 
<stopbits>1</stopbits> 
<parity>none</parity> 
<flowcontrol>none</flowcontrol> 
</serial>
<autoconnect>
<state>on</state>
<trigger>data</trigger>
<service>raw</service>
<desc></desc>
<address>10.4.112.9</address>
<port>2222</port>
<pattern></pattern>
<strip_pattern>off</strip_pattern>
<keepalive>on</keepalive>
<nodelay>off</nodelay>
</autoconnect>
</set_setting>
</rci_request>