Release Notes PN 93000452 Digi AccelePort RAS Adapter Driver Version 5.0.307.0, 08/14/2002 Microsoft Windows NT 4.0 Service Pack 5 and greater Software Package PN 40002249 CONTENTS Section Description ------------------------------- 1 Introduction 2 Supported Products 3 Additional Notes 4 History 1. INTRODUCTION This document describes the device driver that supports the Digi devices listed below. The driver is for use in the Microsoft Windows NT 4.0 environment and is compatible only with Service Pack 5 and greater. Refer to the following number when searching the Digi International Inc. Web site (www.digi.com) or the FTP site (ftp.digi.com) for the latest software package: 40002249_ 2. SUPPORTED PRODUCTS Digi AccelePort RAS 4 Adapter Digi AccelePort RAS 8 Adapter 3. ADDITIONAL NOTES On-line help is available when you install the product. Installation documentation can be found at Digi's Web site, http://www.digi.com, or at Digi's FTP server, ftp://ftp.digi.com. 4. HISTORY Version 5.0.307.0 (M1P) ----------------------- CHANGES Removed support for AccelePort Xp, DataFire RAS, and DataFire SYNC adapters Assigned new part number and released driver as new product BUG FIXES None Version 4.0.229.0 (L Release) ----------------------------- BUG FIXES Fixed: DataFire Sync configuration dialog for X.25 does not show up. (#8068) Fixed: WanLinks driver does not remove keys from SERIALCOMM when uninstalled (#8412) Fixed: The DigiAsyn.sys driver is hanging in an endless loop (#7656) Fixed: Parity error detection failure with AccelePort Xp (#7542) Fixed: Microsoft FAX does not work with AccelePort Xp (#5702) Fixed: Unable to print with AccelePort Xp (#5081) Fixed: Multiple issues with E1/R2 parameter configuration (#7956, #7897) Fixed: The DigiAsyn.sys driver does not handle zero length read requests correctly. Fixed: Some timed-out writes are being inadvertently completed with STATUS_CANCELLED Fixed: Write timeout does not work when Write Complete When Sent option is enabled Fixed: If low latency is enabled, any attempt to open the port causes the system to completely lock up Updated DataFire RAS firmware to M release. Detailed information about firmware enhancements and bugfixes can be found in the DataFire RAS firmware Release Notes. Version 4.0.217.0 (L3P) ----------------------- BUG FIXES Fixed: Caller DID option within Windows 2000 server is not working (#5576) Note: Fixed for AccelePort Xp only. Fixed for Windows NT 4.0 too. Fixed: E1/R2 GroupB and backward signalling range incorrect (#5653) Fixed: Add Channel Mapping option for DataFire RAS24/48/30/60 CT1 and PRI (#7380) Fixed: Driver does not start when installing L2P from scratch (#7582) Fixed: Ntperf reports same throughput on AccelePort Xp port at these baud rates - 1200 2400 4800 9600 19200 (7570) Fixed: AccelePort Xp fails the sndrcv test application (#7354) Fixed: Throughput problems with AccelePort Xp at 921kbps on Windows NT 4.0 (#5173) Version 4.0.214.0 (L2P) ----------------------- BUG FIXES Fixed problem establishing a fax connection (#7220,#5702) Fixed serial printing errors (#7493) RasAudio.exe was missing from the build (#7234) Fixed DigiInf.dll load issue (#7231) Changed Sync2000 PLX9080 setup to initialize in PCI 2.1 mode. Problem with modem country setting for E1/T1 cards (#5073 & #6376) Port Assist Viewer does not display RAS30/60 boards in E1R2 mode (#5071) Port Assist Viewer does not show ISDN layer 3 status (#3976) Port Assist Viewer faults when clearing statistics (#2495) Version 4.0.210.0 (L1P) ----------------------- This version was not released to the public.